I am from Belgium. Since october 2025, we have a Vitocal 250-A with 2 internal pumps (both for floor heating) and a boiler vitocell 100-V 300 Liters. - Internal Pump 1 = floorheating groundfloor - Internal Pump 2 = floorheating 1st floor New construction house with triple glazing and 20 cm insulation everywhere. Since the beginning the 2 floorheatings did not work at same time. The second pump (1st floor) was always dominant. Thanks to this community / forum I have found out how to make both floors work at same time. The solution was to create a significant depature temperature difference. For example: 30°C for pump (1 ground floor) and 27°C for pump 2 (1st floor) Only this way both floorheatings work at same time. If there is less than 2 degrees difference, then there ground floor is not working. Weird but now it works, so I am happy. This was the only problem till October 2026. Now since october 2026, we have 3 new BIG problems: ---> Heating system started again. Problem 1: 40% less water flow compared to the period before the summer. We did NOT use the cooling function during the summer. So both heating circuits were closed from june till end of september 2026. Problem 2: Pump nr 2 (1st floor) was suddenly broken after 2 days of normal working. Viessmann Belgium replaced it. First time with another pump, they said. Second time with the good one, they said. Problem 3: The water from the boiler is not as hot as before the summer. Before the summer: The water felt very hot, even when the sensor in the App showed 50°C. Now the water feels much colder, even when the sensor in the App shows 62°C. Before the summer we could take easily 4 showers without any problems. Now the second shower gets cold water. The temperature of the boiler drops very fast. So the heat pump must start to produce hot water. Once this hot water process starts, during the first 5-6 minutes, the boiler water temperature drops even faster to 34 - 36°C. The water gets colder instead of getting hot. Then suddenly the electric back-up launches automatically and consumes over 7 kW during 40 minutes to warm up the boiler to 50°C or higher. If we take 1 normal shower of 8-10 minutes with water which is not warm at all, the same process starts again. We are not abusing, we are not using too hot water or too much water. All usage is exactly same as before the summer. The installation company Schoonians Steven is a true disaster. Zero knowledge. Viessmann Belgium is now in contact with me since 1 month. They made a firmware update 2 weeks ago when they replaced that broken pump nr.2 After their intervention their was suddenly a terrible loud noise coming from the internal unit. A terrible permanent hard noise. Night 1 = no sleep possible Day after = I contacted Viessmann Belgium, but they say me that its not possible, they say they did not change anything.... They let me down do I decided to go into the service parameters. I saw that they had put both internal pumps to 95%. ---> This was making that terrible noise. I have now reduced both pumps to 70%, now that noise is gone. I think that they put the pumps on 95% to cosmetically create more flow. But it did not work. I still ask them on how much % these pumps were before their intervention. But they dont answer. Since there was zero noise, I guess it was 70% like now or even lower. They are letting me down completely. They lie to me and say that I have messed up everything which is absolutely not true. They have sent me an E-mail today in which they write that they can see that I have activated the electric backup heating for the boiler water. Honestly, since 2 weeks I am searching to deactivate it. But there is nowhere an option to do it. Now I must heat up the boiler every day till 62-63 degrees. This is the only way we can take very fast 2 showers after each other. The water flow is still 40% less than before the summer. I don't know what to do. PLEASE HELP SOGUT Bayram Stichelgatstraat 21, 1700 Dilbeek / Belgium
[email protected] 0032 485 95 99 86
... Mehr anzeigen